Step 1: Unplug the circular saw or remove the battery. … Step 2: Remove the arbor nut from the circular saw blade. … Step 3: Remove the worn blade. … Step 4: Change the old circular saw blade with a new one. … Step 5: Replace the arbor nut. … Step 6: Test the new circular saw blade.
How do I put the blade on my Craftsman first circular saw?
- Step 1: Unplug the circular saw or remove the battery. …
- Step 2: Remove the arbor nut from the circular saw blade. …
- Step 3: Remove the worn blade. …
- Step 4: Change the old circular saw blade with a new one. …
- Step 5: Replace the arbor nut. …
- Step 6: Test the new circular saw blade.
How do you know when to change your circular saw blade?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
How do you loosen the blade on a circular saw?
Press down on the saw’s arbor-lock button and rotate the blade until the locking mechanism engages. Use the blade wrench to remove the arbor nut holding the blade in place. To loosen the nut, turn the wrench in the same direction as the blade cuts. Retract the saw’s upper blade guard and remove the old blade.Which way does a saw blade spin?
Like miter saws, table saw blades rotate clockwise, meaning the teeth should be pointing down.
What are 4 steps to changing a saw blade?
- Disconnect the power. …
- Remove the throat plate and blade guard. …
- Raise the blade. …
- Loosen the arbor nut. …
- Remove the arbor nut with your hands. …
- Remove the blade and replace with the new one. …
- Replace the washer and the arbor nut. …
- Tighten the arbor nut.
What tools are required to change the blade on a circular saw?
- When preparing to change a blade on a circular saw, it is imperative that you unplug the saw or remove the battery. …
- Most saws have an attached wrench, either an Allen type or a blade wrench with a hole that fits over the arbor nut. …
- Knowing the structure and make-up of your saw is important.
What is the first step in changing the blade on a circular saw?
- STEP 1: Unplug or Remove the Battery from the Circular Saw. …
- STEP 2: Push and Hold the Blade Lock. …
- STEP 3: Loosen the Arbor with the Allen wrench. …
- STEP 4: Figure out which way the blade should be installed. …
- STEP 5: Tighten the arbor.
Why does my circular saw blade stop spinning?
The most common reason your circular saw blade stops spinning is because your workpiece is pinching the blade. … Other reasons your circular saw blade could be stop spinning are your blade isn’t deep enough, your blade is dull (Very Common), loose clutch bolt, dead battery, power cable issue or motor issue.
What do you do with old saw blades?Your local recycling should have a metal recycling bin onsite. Steel is easy to recycle, and it can be quite valuable, so it is in the company’s (or the county’s) best interest to collect as much of it as they can.
Article first time published onCan you put a circular saw blade on backwards?
Yes – a circular saw blade can be accidentally mounted on the saw backwards – but it is a mistake you will only make one time because you will find out the instant you try to cut a piece of wood. It will not cut and you will be embarrassed at your mistake.
Do circular saws spin clockwise?
Circular Saws This means that the circular saw cuts wood on the upstroke. For a right handed circular saw (most common), this means that the blade rotates counterclockwise, which is similar to the table saw. For a left handed circular saw, the blade rotates clockwise.
How do you remove the blade from a craftsman saber saw?
- Turn off and unplug the saw from the power source.
- Remove the Allen wrench from the saw’s holder. …
- Insert the Allen wrench into the hole on the side of the saw body toward the front, where you can first see the blade sticking out. …
- Loosen the blade clamp screw with the Allen wrench. …
- Slide the blade out from the clamp.
How do you raise the blade on a Craftsman miter saw?
To lock and unlock the pin, the blade must be in the farthest down position. The pin will not unlock, even though the saw is down. You must push the saw down as far as it will go, then pull the pin out to release the blade.
