Power the unit down by turning off the circuit breaker(s) or fuse(s) for one (1) minute.Power the unit up by turning on the circuit breaker(s) or fuses(s),Monitor the the product for one (1) minute to ensure the error code does not return.
Why does my stove say PF?
The “PF” indicates a power failure. This would be normal to happen when the circuit breaker was flipped OFF and back ON. The “Clock” must be set before all the other functions will be available. You will need to press “Clock” and set the clock and your oven should operate normally.
How do I reset my Whirlpool oven after a power outage?
Look for “Control Lock” on the oven control console and then reset by typically holding the button(s) for 3 seconds.
How do I reset my Whirlpool electric stove?
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Start a bake cycle.
- Monitor the oven for one (1) minute to ensure the error code does not display again.
- Verify oven operation.
How do I fix F1 error on Whirlpool oven?
F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.
Why is my Whirlpool oven not heating up?
An electric oven not heating up can often be attributed to a defective bake element. This Whirlpool oven heating element is a metal coil located at the bottom of electric ovens. When you turn on the oven, wires inside the coil receive electrical current that heats the metal, providing the heat you need to cook food.
What does F1 mean on Whirlpool oven?
This error code indicates the electronic control has detected an internal malfunction or it could have sensed a runaway temperature condition. The sensor will need to be checked first before replacing the control. To check the sensor set the oven temperature to 350 and let it cycle at least 3 times.
How do I reset my oven?
Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.What does PF mean on a Whirlpool refrigerator?
The PF Error code indicates that the unit has experienced a power failure during operation.
How do I put my Whirlpool oven in diagnostic mode?Enter Diagnostics mode by pressing CANCEL>CANCEL>START within a 5-second period. Entering Diagnostics mode will cancel any active oven operation. Enter the Diagnostics mode only after the oven is cool. All elements (depending on which cycle is being used) will operate with the oven door open.
Article first time published onHow do you unlock the control panel on a Whirlpool stove?
Press and hold on to the lock for 3 seconds to lock the control panel. The light above the lock will turn on. Press and hold LOCK for 3 seconds to open the control panel.
How do you reset a stove after a power outage?
If a recent power outage has occurred, turn off the household circuit breaker for the range for one (1) minute. Then reset the circuit breaker and monitor the range for one (1) minute to ensure the error code does not display again. Verify range operation is normal.
Why is my oven not working after a power outage?
Check the Breaker – A damaged or compromised breaker is the most common cause of performance problems. Check the breaker and reset it to see if the oven is working. … Check The Fuse – Many ovens are connected to fuses that react to an electric surge. Check it to see if it is damaged or has scorch marks.
How do you unlock a Whirlpool oven without power?
Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
How do I fix F1 error on stove?
You can try resetting the range by disconnecting it from the outlet or switching off the circuit breaker of the home for 10-20 minutes then restore the power. If the reset doesn’t work your range may have one of the above failures.
Why does my stove say F1?
The F1 error means that there is an electronics failure within the oven. This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor. … The error can also indicate data corruption within the oven’s electronic controller.
How do I fix F1 error on my oven?
On some models it is possible that F1 could also be caused by a keypad problem. In this case it will specify in the tech sheet to power down the oven, disconnect the keypad then power the oven back on, wait for a few minutes to see if the error reappears. If the error reappears it is definitely the control board.
How do I clear my Whirlpool f9e0 code?
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
What does E1 mean on Whirlpool stove?
The E1- F5 error is a door lock error. If these suggestions don’t help, you will need a technician to diagnose and repair the problem. Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
How do I know if my oven temperature sensor is bad?
- Longer Than Usual Cooking Times. …
- Undercooked Foods. …
- Uneven Cook on Your Meals. …
- Overheating Issue. …
- Solving the Problem With a Troubleshooting Tip. …
- Trying out an Ohmmeter. …
- Discovering a Combination of Problems. …
- The Oven-Board Failure.
How do I know if my oven heating element is bad?
- The Element Isn’t Bright Orange. …
- The Element Has Signs of Wear. …
- Food Isn’t Cooked or Is Partially Cooked. …
- The Oven Is Dirty. …
- Your Electric Bill Has Noticeably Increased.
What does PF error code mean?
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. … During a power outage, if there was an unexpected amount of power supply line “noise” that the control detected as an incorrect voltage amount, the control could display the PF Error Code.
How do I put my Whirlpool refrigerator in diagnostic mode?
To start with we need to start the refrigerator’s diagnostic mode. To do this open the refrigerator door and press one or both door switches, depending on your refrigerator type. Next press the refrigerator temperature (+) button three times in ten seconds and release the light switch or switches.
What does PF code mean on dryer?
The PF Error Code is an indication that the drying cycle has been interrupted by a power failure in your home. Touch the POWER button to clear the display. Restart the Dryer.
Why is my stove top working but not my oven?
In most common cases, this specific issue means that the broil element and the baking element remain functional. However, there’s probably a blown internal fuse. If it’s not the fuse, it could be the temperature sensor, broken or frayed wiring, or even a breakdown of the oven control board.
What is wrong with my electric oven?
Common electric oven problems include a broken wire; a bad control, bake, or broil element; or the wrong amount of power coming to the unit. Common gas oven problems include a faulty gas control, igniter, or valve.
How do I read a Whirlpool error code?
Error CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,
What does F5 mean on a Whirlpool stove?
The F5 on most Whirlpool ranges will indicate that you have a problem with the oven door latch assembly or the oven door switch. Since you are seeing this error code when you are trying to set the self cleaning mode, this is likely the problem with your range. You could have a problem with the door switch.
Why is my Whirlpool stove beeping?
A Whirlpool oven can keep beeping because of a faulty temperature gauge, control panel or keypad. Continuous beeping from your Whirlpool oven could indicate a problem. Sometimes you can resolve it by simple pressing the cancel button and resetting the oven.
How do I turn off the Control Lock on my Whirlpool stove?
To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
What does Control Lock mean on Whirlpool stove?
The Control Lock avoids unintended use of the surface cooking areas. If Control Lock is activated when power to the cooktop is off, the cooktop is locked out, and the surface cooking areas cannot be turned on by the cooktop touch controls.
