How do I reset my electronic throttle body

Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.

How do you reset a GM throttle position sensor?

The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.

How do you adjust the idle on a GM throttle body?

Unplug the IAC valve located on the passenger side, rear of the throttle body. Start the engine. Insert a T-30 size Torx driver into the Idle adjustment screw that is located behind the plug removed earlier. Turn the screw to adjust the idle speed to 650 RPM +/- 50 RPM.

Does a throttle body have to be programmed?

In fact, on some engines a new throttle body needs to be programmed with a factory, or equivalent, scan tool. The technician cannot even clean the carbon out of the throttle body in some cases without setting a “check engine” light.

How do you reset the ECM on a Chevy truck?

Remove the nut off the negative battery cable with a socket set or wrench. Slide the cable off of the battery and put it aside. Turn the headlight switch to the “on” position to drain the ecm of any remaining power. Wait at least 10 minutes, then turn it back to the “off” position.

How do I reset my GM IAC valve?

Turn the ignition ON and leave on for several seconds then turn the ignition OFF to allow the ECM to reset the IAC valve. You should be good to go.

Does a throttle position sensor need to be calibrated?

Once you have fitted a Throttle Position Sensor, or TPS, you will need to calibrate it from within MEITE. The signal on the chosen pin should sweep from approximately zero to five volts as you move the throttle from fully closed to fully open. …

Do you have to reset computer after replacing throttle position sensor?

After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset. … The engine light will go out and clear all codes as it goes into a learn cycle.

What is a P1516 GM code?

Error Code P1516 is defined as Throttle Actuator Control Module Throttle Actuator Position Performance. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes. Rather, it applies only to specific vehicle makes, such as GM (Chevrolet/GMC), Saturn, etc.

What happens when you unplug throttle position sensor?

The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it’s running.

Article first time published on

What are symptoms of a bad throttle position sensor?

• An unexplainable bucking and jerking in the vehicle.
• Sudden idle surges.
• Sudden engine stalling without any apparent reason.
• Hesitation while accelerating.
• Sudden surges in speed while driving on the highway.
• Intermittently flashing of check engine light for no apparent reason.
• Difficulties in changing gears.

Can a throttle body be adjusted?

For those customers who want even better performance the throttle body the throttle position sensor (TPS) can be adjusted.

What does diagnostic code P0123 mean?

Diagnostic Trouble Code (DTC) P0123 code stands for “Throttle/Pedal Position Sensor “A” Circuit High.” … It monitors the throttle blade angle and relays this information to the throttle actuator module or powertrain control module (PCM).

How do I calibrate my accelerator pedal position sensor?

To recalibrate the ECM and accelerator pedal, the ignition switch must be in the ON position and then the accelerator pedal must be slowly and fully depressed from idle to full throttle. Repeat the procedure three times.

How do you adjust the throttle sensor on a GM?

Loosen the throttle position sensor retaining screw with a Phillips-head screwdriver. Adjust the TPS by moving it back and forth until the voltage is between 4.0 and 5.5 volts. Hold the TPS in place and tighten the retaining screw with the Phillips-head screwdriver.

What causes a P0507 code?

The P0507 code is triggered when the Engine Control Module (ECM) detects that the engine is idling higher than the specified idle rpm range. The standard engine idle is usually between 600-800rpm based on the model of the vehicle.

How do you reset a GM transmission control module?

1. Step 1: Turning Key Position.
2. Step 2: Press gas pedal.
3. Step 3: Keep Waiting.
4. Step 4: Turning the Key Off.
5. Step 5: Releasing Gas Pedal.
6. Step 6: Wait Again.
7. Step 7: Ready.
8. Identification.

Can you reset a body control module?

To complete the body control module reset, you will have to reconnect the battery. This reestablishes the electrical supply through the BCM as well as other electrical peripherals of the vehicle. Once the battery is reconnected, check if the problems that made you perform the body control reset have been rectified.

Where is the throttle actuator control module located?

The TAC module is mounted on the driver’s side firewall under the corner brace. There are 2 connectors plugged into the bottom of it, one 10 pin and one 16 pin.

Where is the throttle actuator control?

The throttle controller is located on top of the engine between the air intake and the intake manifold.

What does the TAC module do?

The TAC module is the control center for the electronic throttle system. The TAC module and the PCM communicate via a dedicated redundant serial data circuit. The TAC module and the PCM monitor the commanded throttle position and compare the commanded position to the actual throttle position.