Press the “More” button to cycle through each salt level, and then press the “Less” button to choose and save the display as the new salt level. The “PWR”, “Cell”, “Life”, and “Flow” lights will flash 4 times, then the mode exits to normal.
What should my salt generator be set at?
We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.
How do I know if my Pentair salt cell is bad?
- The power center displays a Check Salt message. …
- The Cell Warning light displays consistently, shutting off for only a short while after cleaning.
- Voltage is higher than normal.
- Amperage is irregular (it should normally be zero or just slightly above)
How do you recalibrate a Hayward salt Cell?
- Before recalibrating, test the water with salt water test strips to determine the correct salt level. …
- With the pump running, move the main switch from “Auto” to “Off” and then back to “Auto”. …
- Once you hear the click, immediately push the Diagnostics button 5 times.
How do you reset a Zodiac Tri chlorinator?
Press and hold the MINUTE button until the hours for the power pack and the cell are displayed. Press the HOUR button once to reset the hours for the cell.
How do I reset my Hayward salt cell after cleaning?
If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
Why is my salt generator not producing chlorine?
Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. … If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.
Why is my Pentair salt Cell blinking?
Check Cell Light Flashing: This occurs mostly in salt chlorinators over 5 years old, basically it means that the cell has reached its maximum amount of running hours and needs to be replaced.How long should a salt cell last?
This is all possible thanks to your pool’s salt chlorine generator cell. With proper care, a cell will last about five years.
Why is my Pentair chlorinator not working?Inspect the check valve: Unscrew the small check valve assembly connected to the base of the chlorinator body. … No noise indicates the valve is either clogged or broken and should be replaced or sprayed with a water hose to dislodge any debris stuck in the valve.
Article first time published onHow do you test an IntelliChlor salt cell?
Submerge the salt cell in a bucket of pool water, but do not get the wiring connections wet. Turn on the pump and activate the salt system. Put the output on the salt system at 100% for this test. Put the output back to the original setting when you are done.
What should my chlorinator read?
On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.
How many hours a day should a salt water pool pump run?
The average pool system needs to run anywhere between 4-10 hours so you will have to gauge it yourself though testing over time.
How do you calibrate a Hayward salt chlorinator?
Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.
How do I reset my Hayward Aqua Plus?
Turn the filter pump on. You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.
How do I know if I need a new salt cell?
- Looking worse for wear, it’s lost a few plates and the acid baths just aren’t working.
- Your pool is starting to turn green or cloudy, even though your chlorinator is turned up to 100%.
How do I check my cell hours on my Zodiac Tri chlorinator?
Press and hold the SELECT button for about 15 seconds, until you see a second menu appear. Scroll down to OPERATING HOURS. You will see that your cell hours are at 6000 hours or above. Press SELECT.
What is a Zodiac CrossOver?
The Zodiac Tri–XO CrossOver was created to give greater flexibility to all pool owners by incorporating a unique dual menu system that allows you to either configure to using traditional salt chlorination or the popular mineral salt method of chlorination.
Why are my chlorine tablets not dissolving?
If the tablets are not dissolving, and you get a strong smell of chlorine when you open the chlorinator, you probably have a bad check valve in the chlorinator. It is not allowing any water to move through the chlorinator, and any water that is there simply sits there and builds up a yellowish chlorine gas.
How do you reset the logic on a Hayward Pro?
Press the ‘Menu’ until, ‘Default Menu’ appears on the display. This menu is where the ‘Inspect Cell’ message is stored. Press the (>) key, repeatedly, until ‘Inspect Cell, Hold + to reset‘ appears on the display.
What does inspect cell mean on salt water pool?
If both the “check salt” and the “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. Both lights will also stay on if the controller is set to the wrong turbo cell type, or if the cell is unplugged.
How much does it cost to replace a salt cell?
A well-maintained salt chlorine generator will last 3–7 years. Replacing the salt cell costs $700–$1100. Replacing the control board costs $500–$900. You can extend the lifespans by maintaining a consistent salt level, cleaning the cell only when needed, and using the reverse polarity function.
How often should I clean my chlorinator cell?
At the very least, your saltwater chlorinator should be cleaned twice a year, but you should inspect it every two months just to be sure. If it needs to be cleaned, clean it. If it doesn’t, then just give it a good rinse with a garden hose.
What does no flow mean on salt cell?
The “No Flow” light indicates that the flow switch is not detecting sufficient water passing through. Check the following: cleaning the cell or the filter (see how to backwash a DE Filter or Clean a Cartridge Filter). Replace the flow sensor.
