How do I reset my Whirlpool Duet HT washer

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do I reset Whirlpool Duet front load washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

How do you reset a front loader washing machine?

1. Press POWER to turn the washer off.
2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
4. Plug the washer back in, or turn the circuit breaker back on.

How do I reset the control panel on my Whirlpool Duet dryer?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

Where is the dryer reset button?

Often, dryers are equipped with a reset button on the control panel.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

How do I reset my Whirlpool load and go?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

How do I reset the code on my Whirlpool front load washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I reset my Whirlpool auto load sensing washer?

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
3. The motor has now been reset and is ready for you to start a cycle.

Does unplugging a dryer reset it?

Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.

Article first time published on

Why is my dryer running but not heating?

Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.

How do I turn off the Control Lock on my Whirlpool Duet washer?

1. Locate the “Control Lock/Unlock” button on your Duet’s control panel. …
2. Press and hold the “Control Lock/Unlock” button for three seconds.
3. Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.

How do I turn off the Control Lock on my Whirlpool dryer?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

When I push the start button on my dryer nothing happens?

A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting. Some dryers use a motor relay to control the drive motor, so a broken motor relay can prevent the dryer from starting. … In electric dryers, a blown thermal fuse can keep the dryer from starting.

How do I reset my Whirlpool Duet dryer F01?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.

How do I reset my condenser dryer whirlpool?

1. Turn on the tumble dryer main power.
2. Within 10 seconds turn the program selector from off to teh 6 o’clock postion, pointing straight down.
3. Push the “Start” button three times.
4. Turn the program selector to the “one” position which should be the CW or airing program.

Where is the thermal fuse on a Whirlpool Duet dryer?

Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.

How do you unlock a Whirlpool Duet washer?

Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.

How do I reset my washing machine after error code?

Restart it: If you think it might be a digital problem, try the old reset trick. Turn the washing machine off at the powerpoint for at least 60 seconds, and then turn it back on. With a little luck, the master reset should restart the wash programs.

How do I reset the touchscreen on my Whirlpool washing machine?

1. Press PAUSE/CANCEL twice to cancel the cycle. …
2. Press POWER.
3. Select the desired wash cycle.
4. Select the desired Modifiers and Options.
5. Press START.

Why is my washer stuck on sensing mode?

When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.