How do you change a drive belt on a Craftsman 42 lawn mower

AYP / Craftsman / Sears Deck Belt fits 42″, 46″ & 50″ Decks built since 1995. Size: 1/2″ x 95-1/2″.

What size belt does a Craftsman 42 inch cut take?

AYP / Craftsman / Sears Deck Belt fits 42″, 46″ & 50″ Decks built since 1995. Size: 1/2″ x 95-1/2″.

What size belt do I need for a 42 inch deck?

There’s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.

How long is the drive belt on a Craftsman riding mower?

CRAFTSMAN 42-in Drive Belt for Riding Mower/Tractors (11/16-in W x 40.9-in L)

How many belts are on a Craftsman riding lawn mower?

The three primary belts found in a Craftsman mower are the drive belt, power clutch belt and arbor belt.

How do I know what size deck belt I need?

Place one end of the tailor’s tape measure on the mark, then extend the tape measure around the inside circumference of the circle until you reach the mark with the other end of the tape measure. Take your reading from the tape measure to determine the size of the belt.

What size belt do I need for a 42 inch waist?

Pants SizeBelt Size OWBBelt Size IWB414546 or 47424647 or 48434748 or 49444849 or 50

How do you tighten the belt on a Craftsman lawn mower?

Push the belt keepers on the transaxle pulley down and slide the belt over the transaxle pulley. Pull the slack from the back of the tractor (transaxle pulley) and slide the belt on to the stationary and clutch idlers. This will increase the tension in the belt and hold it in place.

What is Ground drive belt?

The ground drive belt connects the engine crankshaft to the transaxle pulley to drive the rear wheels. If the belt breaks, the lawn tractor won’t move. If the belt is worn, the lawn tractor moves sluggishly because the belt slips on the pulley.

What size drive belt does a Craftsman?

AYP / Craftsman / Sears Drive Belt No. AYP / Craftsman / Sears Drive Belt fits 42″ mowers, 12-18 HP. Size: 1/2″ x 92-1/4″. Replaces part numbers 532130969 and 130969.

Article first time published on

How much is a drive belt for Craftsman riding mower?

This item Replacement Riding Mower Drive Belt 138255 / 160855 Replacement for Craftsman 42″ & FITS POULAN HUSQVARNAAdd to CartCustomer Rating4.5 out of 5 stars (382)Price$1798ShippingFREE Shipping on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime

What is the ground drive belt on a Craftsman riding mower?

Description: This replacement belt for the ground drive is an authentic component commonly used with Craftsman riding lawn mowers and garden tractors. It is the belt that connects the engine crankshaft pulley to the transmission pulley allowing the mower to drive.

What size belt goes on a 42 inch deck Cub Cadet?

Cub Cadet Deck Drive Belt fits 42″ Cut Decks No. Size: 1/2″ x 96-1/2″. Replaces # 954-04060B & 754-04060B.

What causes a mower deck belt to come off?

The drive belt may come off a riding mower because it is damaged or loose. … If broken or worn, the belt can break while the engine runs, and it can fly off at a great velocity, which is highly dangerous. Check the belt for looseness, cracks, fraying or separation from the rest of the assembly, and replace if necessary.

When should a drive belt be replaced?

It is often beneficial to change the drive belts in your car approximately every 60,000 to 100,000 miles. By undergoing annual car inspections, you can have your drive belts evaluated. If any signs of damage or severe wear and tear are identified, the belts can be replaced.

How much does it cost to replace a drive belt?

Once the belt starts to wear thin or breaks, it will need replacing, if those parts are going to work as they should. You will pay between $120 and $160 for this replacement job. The labor should cost about $80, while parts will run you about $60.

Is a drive belt the same as a Cambelt?

A drive belt connects to accessory components like your car’s AC, alternator, water pump and power steering pump. A timing belt connects the crankshaft to the camshaft(s) and in some cases, the water pump.

How do you pick the right size belt?

The most widely used method is to buy a belt that is 1-2″ larger than your pants size, or as some say: ONE SIZE UP. Example, if you wear a size 36 pants, you would order a size 38 belt. We do not make odd sizes (33, 35, 37, etc.) so you would have to go with a belt that is 2″ larger.

What hole should a belt fit on?

Good quality belts usually have 5 holes. You should then be able to wear the pin of the buckle in the third (middle) hole. The belt’s tail size will then be automatically in the right proportion. When buying a belt online, you can choose the right size by using proper ‘Size Guides’.