How do you check a GE dryer start switch

If yours is a two-wire switch, touch one tester probe to each of the switch’s terminals. You should receive a reading of infinity. While the probes are still touching the switch’s terminals, press in on and hold the switch. The reading should change to zero.

How do you test a start switch?

If yours is a two-wire switch, touch one tester probe to each of the switch’s terminals. You should receive a reading of infinity. While the probes are still touching the switch’s terminals, press in on and hold the switch. The reading should change to zero.

When I press the start button on my dryer nothing happens?

A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting. Some dryers use a motor relay to control the drive motor, so a broken motor relay can prevent the dryer from starting. … In electric dryers, a blown thermal fuse can keep the dryer from starting.

Why will my GE dryer not start?

If your dryer will not run or start, check the following: Make sure the dryer plug is pushed completely into the wall outlet. Check that the dryer door is closed tightly. Make sure that the cycle selection button is positioned on the desired temperature, fabric and drying time.

How does a dryer start switch work?

The dryer’s start switch is a momentary contact push switch that allows electricity to energize the motor. Once the motor has begun to spin, an expanding contact within the motor, called a centrifugal switch, expands to maintain contact after the start switch has been released.

Is there a reset switch on GE dryers?

You can find it on the control panel or the front of the plug. Press it to reset the GE dryer. … Give it ten minutes to cool before reconnecting the dryer and turning it on.

Where is door switch on dryer?

Locate your dryer’s door switch. It will be located around the door opening in the front panel. You may be able to pop the switch out of place, or remove it by removing only a single screw. If you are unable to access your dryer’s door switch this way, you will have to remove the front panel of your dryer.

Where is thermal fuse on GE dryer?

In GE dryers, the thermal fuse–sometimes called a safety thermostat–is located behind the drum on the inside of the dryer. To access the thermal fuse you will need to open the dryer from the top.

Why does my dryer only work when I hold the Start button?

From the description of your problem the most likely cause of this is a bad motor relay but the problem can also be a bad control or connection. The good news is if the dryer runs when the start button is pressed then the timer, push to start switch, motor and door switch are all okay.

What happens when a thermal fuse blown on dryer?

A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. … When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again.

Article first time published on

Why did my GE dryer stop working?

When the dryer stops working again due to a replacement fuse or circuit breaker problem in the electrical panel, the terminal block may be at fault. … The blown fuse and breaker trip will have stopped the GE dryer from working.

Why does my dryer not start?

Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: … If the drum light doesn’t turn off, a failed door switch is the likely reason the dryer won’t start. A blown thermal fuse often prevents an electric dryer from starting.

How do you reset a GE dryer?

How do you reset a GE dryer? Turn the dryer off, then on again to reset it. Or you can press the reset button on the dryer plug.

Where are the fuses on a dryer?

Locate the Fuse Thermal fuses are installed on the dryer’s exhaust duct. Typically, you must remove the back panel of a dryer to access the fuse.

Where is the door switch located?

THE DOOR SWITCH IS THE FIRST PATENTED DOOR SENSOR The Door Switch is the only door sensor that extends above the top of the door.

How do I unlock my GE dryer?

To lock and unlock the dryer controls: Press and hold the Extended Tumble and – (minus) buttons for 3 seconds. The control lock icon will flash while locking/unlocking, stay on when locked, and turn off when unlocked. NOTE: The Power button can still be used when the machine is locked.

How dO I know if my dryer thermal fuse is blown?

Unplug your dryer and ensure it is no longer connected to the gas or electric.
Locate the thermal fuse, as above.
Disconnect the thermal fuse from the wires.
Test the fuse with a multimeter.
If the needle on your multimeter does not move, your thermal fuse is blow.

Will a dryer start with a blown thermal fuse?

Will the dryer run if the thermal fuse is blown? … While a blown thermal fuse is the most common reason a dryer won’t start, run, or heat, you should remove the fuse from the appliance and test it to determine if it has blown or not before purchasing a new one.