How do you light a Honeywell pilot light

Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.

How do you light a pilot light on a Honeywell gas furnace?

Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.

How do you light a gas water heater with an electric pilot?

Turn the gas knob to “Pilot,” press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold. While still holding the gas down, light that pilot.

How do you turn on a pilot light?

Turn the gas regulator valve to the “pilot” position. If the water heater has a manual “ignite” button, press that to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites.

What would cause a pilot light to keep going out?

A faulty, misaligned, dirty, or damaged thermocouple is often the culprit behind your pilot light going out. The thermocouple is an automatic safety shutoff device that prevents the gas valve from opening if the pilot light is out.

Should the pilot light always be on in a gas heater?

Most furnaces with electronic ignition have a device called a hot surface igniter. … The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.

What does blinking light on water heater mean?

If the Status Light is flashing once every three seconds, the pilot light is lit and the gas control valve is working properly. Make sure the gas control valve is turned to “Hot” and wait for the water heater to heat back up. It may take several hours for the water to heat up.

How do you light an automatic pilot light?

Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Does an electric water heater have a pilot light?

There’s no gas or pilot light involved in electric water heaters. If the power to your electric water heater is off, you may have an electrical issue requiring professional assistance. You will not need to reignite the water heater if you have a newer model equipped with an automatic pilot light.

Article first time published on

How do you light a gas water heater?

Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.

How do I set my Honeywell heater?

Press the “System” button to put the thermostat in Heat, Cool or Off mode. To change the setting, push the button again. The screen will display the setting you’ve selected. On the right side of the display, the up and down arrow buttons operate the temperature settings.

How do I check my pilot light?

1. Locate the front cover panel on your furnace. It should be a little door that’s easily visible. …
2. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame.
3. If you don’t see a flame, your pilot light is out.
4. If there is a flame, check the color.

Should the water heater be on pilot or on?

You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.

How do you fix a gas fire that keeps going out?

1. Before You Begin: Is Your Pilot Light Lit Inside Fireplace?
2. The Fix: Pilot Light to Gas Fireplace Won’t Stay Lit.
3. Check Your Thermopile Output with the TH/TP Contacts.
4. Don’t Replace Your Thermopile or Thermocouple Right Away.
5. Cleaning the Thermopile.
6. Re-test the Cleaned Thermopile.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

How do I know if my furnace is gas or electric?

If you see a blue flame, it’s a gas heat exchanger. Other units will have a small metal panel that’s easy to remove. You can check behind there to see if you see that blue flame. Electric systems don’t have that access window or panel and make very little noise.

Should water heater light be blinking?

1 flash every 3 seconds means the pilot is lit and the gas valve is working normally. A solid red status light means the water heater is shutting down. … The status light will flash more than once every 3 seconds if an error is detected.

How do I reset my water heater?

Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.

How long does it take a hot water heater to heat up?

Your average gas tank water heater takes about 30 to 40 minutes to heat water once it gets in the tank. This preliminary heat up happens when new water from your water supply is fed into the tank.

Does leaving the pilot light on use gas?

A pilot light is a small flame that is kept alight using a steady, small stream of gas. This continuous flame is necessary to light large burners such as those found in gas fireplaces.

Do I need to turn gas off if pilot light goes out?

Since the thermocouple regulates gas going to the pilot, it should cut off on its own if the pilot ever goes out, but that’s only if it’s functioning correctly. If the thermocouple isn’t working properly, then it’s possible that it’s allowing gas to leak into the very room where the heater is located.