How do you perform a crankshaft variation learn procedure

Slowly accelerate the engine to 4000 RPM (or indicated RPM for your vehicle). Hold RPM until engine speed drops back toward idle. Release throttle immediately once procedure is learned! Once the variation values are learned, the ECC will return engine control to the driver.

How do you do a crank relearn?

Run the engine until the vehicle reaches normal operating temperature (ECT > ~65C or 150F).
Put the vehicle into Park (auto) or Neutral (manual).
Turn off all accessories including the A/C, heater, and fans.
Turn the vehicle off.
Apply the parking brake.
Press the brake pedal.

What is a crank relearn?

A crank relearn is a process that the PCM goes through to recalibrate its knowledge of the relationship between the crankshaft and camshaft. … Over time, the timing chain/belt can stretch and that stretch changes the relationship and timing between the crankshaft and camshaft.

Do you have to relearn a crankshaft position sensor after replacing?

The crankshaft position sensor relearn needs to be done if the crankshaft position sensor or timing cover, are moved, removed, replaced, or disturbed in any way. The reason the relearn is necessary is to “sync” the sensor with the crankshaft.

What scanner will relearn crankshaft position sensor?

The FOXWELL NT510 GM scanner will relearn the crankshaft position sensor on a 2009 chevy cobalt.

How do you fix crankshaft position system variation not learned?

Repair or replace wiring harness around crankshaft position sensor.
Repair or replace crankshaft position sensor.
Repair or replace crankshaft or related components.
Repair or replace timing belt.
Repair or replace powertrain control module.

How do I relearn a crank sensor without a scanner?

Turn off all of the accessories. …
Accelerate the vehicle to 55 mph at part throttle. …
Cruise at 55 mph for another 5-6 minutes.
Decelerate to 45 mph without using the brakes, and maintain 45 mph for 1 minute.
Perform 4 deceleration cycles, without using the brakes, of 25 seconds each where no specific speed is necessary.

What are the two types of relearn procedures?

The three types of relearn procedures are auto relearn, stationary (manual) and OBD. Some vehicles may use a combination of two or more relearn types.

How long does it take to relearn a crankshaft position sensor?

This can take up to 10 minutes. Do not turn off the engine or disconnect the scan tool during this procedure.

What happens if you don't do a crank relearn?

Remember: That you are going to increase the engine speed to approximately 3000 RPM, 4000 RPM, or 5150 RPM. … Failure to do such will result in over-revving of the engine, causing possible engine damage.

Article first time published on

What scanners can do relearn?

LAUNCH OBD2 Scanner CRP123E Engine ABS SRS Transmission Code Reader. …
LAUNCH Bi-Directional Automotive Scan Tool,31+ Relearn Service, Free Update. …
Autel MaxiTPMS TS501 TPMS Automotive Scan Tool with Relearn Capabilities.

What scan tool can do a case relearn?

The CASE Relearn can be done by anyone with a Tech 2 scan tool, advanced snap-on scanner, or also a Dashhawk or Aeroforce Scan Gauge depending on the vehicle.

How do I fix code p1345?

Loose the distributor hold down bolt with engine OFF. Make sure your OBD scanner is plugged in to monitor the Cam Retard Offset reading. Turn the engine on, let it warm to normal operating temps, and get the rpm’s above 1,000. If your reading is negative, turn the distributor counterclockwise.

What is code P0315?

P0315 OBD-II Trouble Code (Crankshaft Position Sensor Variation Not Learned) By Jerry Renshaw. You probably know by now that an illuminated Check Engine Light (CEL) means that a sensor that monitors a system in your drivetrain has noted a reading outside of normal parameters.

Can I bypass a crank sensor?

No. You just cannot bypass the crankshaft sensor, the car will crank but will not start. The DME needs to see this signal in correlation with the cam sensor for start up and fuel injection sequence.

What does P0016 mean?

P0016 is the OBD-II generic code indicating that the camshaft position sensor for bank 1 does not correlate to the signal from the crankshaft position sensor.

What is P0365 code?

What the P0365 code means. Essentially, the P0365 code means that there has been a lack of voltage detected from the camshaft position sensor B in bank 1 by the PCM within a few seconds of the engine starting. … Bank 1 means that the sensor is located in the engine bank with cylinder 1.

What is a Reluctor wheel?

Also referred to as a tone ring or timing wheel, the reluctor rides on the back of the crank and is read by a magnetic sensor located on the outside of the block near the starter. The magnet reads the teeth on the wheel and this gives the ECU accurate crankshaft position.

Can TPMS sensors be reprogrammed?

Well, it depends on the TPMS sensors. For programmable or configurable sensors, yes. These sensors are designed to be programmed or cloned from an OEM or another aftermarket sensor before they can be used in a vehicle.

How does TPMS activation tool work?

This TPMS tool gives you direct access to your vehicle’s engine control unit and allows you to clear sensors and diagnostic trouble codes. A handheld TPMS tool that will work with 98 percent of cars and trucks by scanning the TPMS sensor’s ID, then inputting the IDs directly into the device.

How does TPMS relearn tool work?

An OBDII relearn procedure requires a TPMS scan tool to transfer new sensor IDs directly to the vehicle’s ECU. The user would need to scan each TPMS sensor, connect to the vehicle’s OBD port, then follow the step-by-step instructions on the tool. The new TPMS sensor IDs are then transferred to the vehicle.

What's a good OBD2 Reader?

#1 Best Overall: Launch CRP129E Scan Tool. #2 Best Bluetooth Scanner: BlueDriver Bluetooth Pro OBDII Scan Tool. #3 Best Budget Scanner: Foxwell NT301 OBD2 Scanner. #4 Autel MaxiCOM MK808 Scanner.

Which scan tool would be the best to use when diagnosing transmission problems?

But if you are trying to diagnose transmission and engine fault codes in a modern car, you are better off with the multi-faceted functionality of the Autel MD802 MaxiDiag Scan Tool. The scanner offers a complete array of OBD2 diagnostic functions. It can scan, read, and erase engine trouble codes.

What is a Tech 2 scanner?

GM Tech 2: This is the GM factory scan tool used in all GM dealers since 1996. … The Tech 2 will allow your shop to be to ‘dealer level’ capable on all covered GM cars. Scan, pull codes, graph data and have all bi-directional controls available for all vehicle systems including Powertrain, Body, Chassis and Network.