To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How do you reset the Salt reading on Aqua Rite?
To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How do I reset my Hayward Aqua Trol salt generator?
To reset, turn the unit to Off and then back to Auto. Wait for the relay to click (5 to 10 seconds). Desired Output % Dial 1 to 100% sets the level of cell operation in % of operating time.. Example: 50% (factory default) cell is operating and generating chlorine 50% of the total pump/filter operating time.
How do you calibrate a Hayward Salt Meter?
Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.What should my salt chlorinator be set at?
We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.
What happens if salt level is too high in pool?
Having too much salt in your pool water can result in unnecessarily increasing chemical expenses. But having too little salinity restricts the amount of chlorine being generated and can lead to algae and bacteria growth.
How do I reset my Hayward salt chlorinator?
Reset AquaRite Salt Chlorination Inspect Cell Light If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
Why is my Hayward salt system not generating chlorine?
The salt level is too high or too low (ideal 3200 ppm). The water temperature is warm and this causes a higher demand for chlorine. The water temperature is too low (below 50ºF) and this causes the Aqua Rite to stop generating. … Note: Any one of these problems will cause a little or no chlorine residual.How do you reset the check light on a Hayward?
You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus (+) key once. This should reset the light and message.
Why is my Hayward salt system not producing chlorine?The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
Article first time published onHow much salt do I add to my saltwater pool?
To reach the initial salt level recommended by the salt system manufacturer (usually 2400-3200 ppm), you will need to add about 200 lbs of pure pool grade salt (NaCl), per 10,000 gallons of water. Salt stays in the water, you only need annual boosters, to replace salt lost to backwashing or splashout.
How do I add salt to my pool for the first time?
To add salt, turn on your filter pump and add the salt directly to your pool water. Use a brush to help the salt dissolve and to prevent the salt from piling up on the bottom of your pool. Run your pump for 24 hours to help distribute the salt evenly throughout your pool.
How do I know how much salt to add to my pool?
- Salt to Add (in pounds) = Gallons x 8.35 x (0.0032 – (current salt ppm / 1,000,000))
- Volume = (width x length x depth) x 7.48.
- Volume = (3.14 x r2 x depth) x 7.48.
What level should I set my chlorinator?
5 Maintenance Tips for Salt Chlorine Generators Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal. Clean the chlorinator cell at least once a season or as needed.
What should my chlorinator read?
On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.
Can you put too much salt in a saltwater pool?
The salt level in your swimming pool should be 3,000 ppm (parts per million). Over-salting will not damage your pool system, but will create salty-tasting water. Highly excessive Salinity levels (over 6,000 ppm) will cause corrosion damage to metallic equipment, such as ladders and handrails.
Can too much salt make a pool cloudy?
Just like a chlorine-based pool, saltwater pools turn cloudy when chemicals are not balanced. You need to ensure that all chemicals are balanced all the time to avoid cloudy water and growth of algae.
What does inspect cell mean on salt water pool?
If both the “check salt” and the “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. … Once your water has been tested, add the salt to your pool to bring the levels back to the recommended 2800 to 3200 ppm.
Why is my salt cell light blinking?
If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires.
How does Hayward chlorinator work?
Water comes into the chlorinator directly from the pump and reenters the main circulation pipe after the heater or filter. … Each Hayward chlorinator has a removable lid that allows you to drop in a slow-release Trichlor chlorine tablet. It also has a flow-control valve that allows you to adjust the flow of water.
How long should I run my salt chlorinator?
Typical pool pump operation is 8 hours per day, although it is not uncommon to run longer in the summer months (or with low speed variable speed pumps) or shorter in the winter when bather loads are light.
