How do you remove the transit bolt on a Bosch washing machine

All new washing machines are fitted with a transit bolts to protect the machine against damage in transit. Transit locks and bolts must be removed before you use your appliance.

Do Bosch washing machines have transit bolts?

All new washing machines are fitted with a transit bolts to protect the machine against damage in transit. Transit locks and bolts must be removed before you use your appliance.

What happens if you run washing machine with transit bolts?

The bolts can rip sections off the outer tank, tear through the outer casing and cause massive damaging vibrations to be sent through the room in which the washing machine is installed. In other words, by not doing as instructed you risk major damage to your washing machine.

What happens if I use my washing machine without removing the transit bolts?

If you don’t remove them, it will have no suspension system so will vibrate VERY badly when you run it. It will likely be pretty noisy. The suspension stops vibration and motion of the drum from being transmitted to the floor. Locking it up solid with the transit bolts means that the suspension is not used.

Do all new washing machines have transit bolts?

Normally when you get your new washing machine there will be two (rare), three or four transit bolts fitted through the rear panel of the washing machine that fix to the outer tank of the washing machine. … These bolts must be removed before the washing machine is used.

Do I have to remove transit bolts?

The transit bolts need to be removed when the appliance is being installed. They are designed to hold the drum in a fixed position while being transported. Failure to remove this will void the warranty, so please refer to the appliance manual for additional guidance.

What size are washing machine transit bolts?

They are typically 4 to 12 in (100 to 300 mm) in length, although any size is possible as it depends on the type of device being transported. The most common example of transit bolts is the securing of the drum of a washing machine while it is transported from shop to property (or property to property).

What happens if you move a front load washer without bolts?

Impact of Moving A Front Load Washer Without Shipping Bolts: In case you could not able to use the shipping bolts, then you have to ensure that there is no water present at the bottom of the tub. … You have to try to get a better hold of shipping bolts if possible so that you can make sure of the safety of the washer.

Is it necessary to remove transit bracket from washer?

Installing and moving your washing machine may require you to remove the transit bolts. These are fitted to hold the drum in position when transporting and will cause the washing machine to move and damage if not removed before use.

Can I lay my washing machine on its side?

It’s recommended you always keep a washing machine in an upright position. Laying a washer on its side can cause the inner and outer tubs to bump against each other, which can loosen support pads or damage the suspension. It can also cause the tubs to move out of alignment and alter the way your unit works.

Article first time published on

How do you install transit bolts?

By sliding the bolt, the bare end of the transit bolt shaft will find the attachment hole on the washing machine drum and literally insert itself. Once inserted, begin screwing the bolt in. Tighten down the bolt with the wrench. The tub will stabilize more after each bolt is installed.

Does Bosch washer need stabilizer?

Does ifb/Whirlpool/Bosch/Lg Front Load Washing Machine Need Stabilizer? A voltage stabilizer is only needed if your area has a higher fluctuation of voltage. If the voltage is normal, there is no need to use a voltage stabilizer. Moreover, these brands are coming up with an inbuilt stabilizer!

What is the best way to lift a washing machine?

The best way to pull a washing machine out, is to open the door and get hold of the door opening at the top of the door seal. Then lift the washing machine up and pull it forward on its back feet. But don’t rush in because there are potential complications you need to avoid.

How do you transport a front load washer?

Slide your front-load washer away from the wall far enough to access the power cord. …
Place a bucket on the floor behind your washer. …
Move your washer from the laundry room. …
Find the shipping bolts that were removed when your washer was first delivered.

How do you stabilize a front load washer for moving?

Wrap & Load Wrap your washing machine in three to four moving blankets until it is completely covered and padded. Hold the blankets in place with a cord or packing tape. Next, get your helper or helpers to carefully lift your machine onto a dolly. Secure the washer to the dolly with ropes.

Can you transport front load washer its side?

How should I transport it? When you move your washer, first replace the shipping bolts that were originally in the back of the washer. … Also, make sure your washer is placed in the moving van upright. Shipping your washer on its side, front, or back can damage it.