How do you reset the change oil light on a 1999 Chevy Silverado

To reset the oil life on your chevy silverado. Turn the ignition to the first position. Do not start the engine. Press the accelerator pedal slowly all the way down 3 times within a 5 second interval.

How do you reset the change oil light on a Chevy Silverado?

To reset the oil life on your chevy silverado. Turn the ignition to the first position. Do not start the engine. Press the accelerator pedal slowly all the way down 3 times within a 5 second interval.

How do you reset the change oil light on a 1999 GMC Sierra?

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the “Oil Life Reset” appears the system is resetting.

How do you reset the change oil light on a 2000 Chevy Silverado?

To reset the 2000 Chevy silverado 1500 oil change light put the engine in the run position without starting the engine, press the gas pedal to the floor 3 times within 5 seconds, and then the change oil light will flash and then you can restart the vehicle.

How do you reset the change oil light on a Chevy?

Within five seconds of turning the key, depress the accelerator fully to the floor three times. 3. Watch for the oil light to flash and turn off. If the oil change light does not turn off, turn the key to the off position and retry the process.

How do you reset the change oil light on a 2001 Chevy Silverado 1500?

Turn the ignition on but don’t start the engine. Press the accelerator to the floor 3 times in 5 seconds. The oil light will flash and reset.

How do I reset my oil change light?

Push the accelerator pedal three times all the way to the floor, in less than 10 seconds. Turn the ignition off, and the light will disappear, resetting the indicator.

How do you reset the change oil light on a 2002 Chevy Silverado?

For the 2002 silverado you just need to turn the ignition to the on position but do not start your vehicle. Press the gas pedal to the floor 3 times within 5 seconds and you should see the change oil message flash if done correctly.

Why won't my change oil light go off?

If you are referring to the oil pressure warning light, it may be that the oil pressure is low, due most likely to excessive wear in the oiling system. Or perhaps just a faulty oil pressure switch or the wire grounding out somewhere. If it is an oil level light there is a problem with the sensor or sensor circuit.

How do you reset the oil light on a Chevy Equinox?

Turn the key in the ignition to the “On/Run” position with the engine off.
Press the “Menu” button for the Vehicle Information Menu.
Press “Up“. The remaining oil life will be displayed.
Press and hold the “SET/CLR” button until 100% is displayed.
Turn the ignition off.

Article first time published on

How do you reset the change oil light on a 2001 Chevy Suburban?

Turn the ignition off and wait 10 seconds. Start the engine, if the change oil light is off you are done, if the change oil light flashes and then goes out turn the ignition of, wait and start the engine again.. turn the key on, but dont start the car. press the gas pedal three times , oil light should flash and reset.

How do you reset the oil life on a GMC Sierra 2021?

Turn the ignition to ON position without starting the engine.
Fully press and release the accelerator pedal 3 times within five seconds.
Turn the ignition off and start the engine to verify the indicator has been reset.

How do you reset the change oil light on a GMC Yukon?

Close all doors, gear to park position.
Turn the ignition on. Don’t start the engine.
Use the scroll button to navigate the INFO menu then press the CHECK button.
Then scroll down to REMAINING OIL LIFE.
While the REMAINING OIL LIFE is displayed. …
Turn Off the ignition.

How do you reset the change oil light on a 2001 GMC Sierra?

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the “Oil Life Reset” appears the system is resetting.
Turn the ignition off and then start the engine to verify the indicator has been reset to 100%.

How do you reset the change oil light on a 2003 GMC Yukon?

Turn ignition switch to ON position with engine off.
Fully depress and release the accelerator pedal 3 times within 5 seconds of turning key.
Change Oil lamp will flash for 2-10 seconds while it resets.
Once it stops flashing, the maintenance light reset is complete.

How do you reset the oil light on a 2000 GMC Yukon?

Put the key in the on position. Keep your foot off the brake and press the START button for 5 seconds.
Go to the OIL LIFE screen. …
Hold down the ✓ button. …
Turn the ignition off and start the engine to verify the oil life has been reset.

How do you reset the dashboard lights?

Open the hood of your vehicle. …
Loosen the nut that holds the negative terminal to the battery with the pliers. …
Completely remove the cable from the negative battery terminal. …
Leave the battery disconnected for 10 minutes to ensure that the computer is fully reset.