How do you tighten a boat throttle cable

Loosen the throttle cable adjuster jam-nut with the wrenches. Extend or contract the adjuster until the cable moves the throttle to the idle position.Push the control lever forward to the “Forward idle” position. … Pull the control lever back, through neutral, into the reverse idle position.

How do I adjust the throttle cable on my inboard?

Grab the end of the lower cable where you just removed it from the stud and pull. While pulling, turn the propeller clockwise. The throttle now is in full reverse position. Move the lower cable up and down until it fits in the slot between the studs.

How do you adjust a shifter cable on a boat?

put the control into full forward wide open throttle position.
Raise outdrive approximately 1/2 the distance under normal trim function (NOT TRAILER). …
have second person rotate prop counterclockwise until solid (no clicking or intermittent engagement) engagement.

How do you adjust the throttle tension on a Mercury outboard?

Adjust the throttle friction with the adjustment screw that’s typically below the throttle on the tiller. Set it until you feel a slight drag on the handle when accelerating or decelerating. Clockwise increases friction, and counterclockwise decreases it.

How does a Mercruiser shift interrupter work?

A shift interrupter switch connects to the shift plate and stalls the engine when you shift in and out of gear to help prevent damage to the stern drive. This switch is directly centered in the assembly when the cable is in the neutral position and activates just as the shift cable places the drive into gear.

What is Mercruiser DTS?

Mercury Marine’s DTS (Digital Throttle and Shift) takes the performance of your boat to the highest level and makes putting the motor into gear a lot smoother and less clunky. … Compatible on many of the larger Mercury outboards, DTS is a whole new experience for single-engine boats.

What does throttle friction knob do?

This Throttle friction device is to be used to eliminate the “throttle creep” on outboards, inboards and stern drives while the vessel is underway for trolling or cruising. NOTICE The Friction knob should only be tightened after the desired throt- tle speed is reached.

How do you adjust an outboard throttle cable?

Loosen the throttle cable adjuster jam-nut with the wrenches. Extend or contract the adjuster until the cable moves the throttle to the idle position.
Push the control lever forward to the “Forward idle” position. …
Pull the control lever back, through neutral, into the reverse idle position.

How do you adjust the idle on a Yamaha 150 outboard?

If you pop the hood off and look on the starboard side of the throttle body, there in the middle area you’ll see the idle speed adjustment screw. Just turn it counterclockwise to back off the idle a little. Should idle around 700 rpms.

What is Throttle drop?

What’s Throttle drop? When you have to push the throttle past where you actually want it to go, so it can drop back down to where you want it.

Article first time published on

What is a shift interrupter switch on a boat?

Re: What is a shift interrupter switch ? This switch allows the drive to shift back into neutral with less effort. If the switch is defective or disconnected it will be very difficult to get neutral. If the shift cable is bad, it can cause the switch to “over-activate” and stall the engine when you shift.

What does OMC Shift Assist Module do?

The electronic shift assist reduces shifting effort by limiting engine RPM. This also results in smoother shifting. When the vertical drive is all the way in forward or reverse gear the overstroke switch shuts off the electronic shift assist.

Where is the neutral safety switch on a Mercruiser?

This is the mercruiser neutral switch on a 7.4 454 engine. It is located behind the transmission.

How do you test a neutral safety switch on a boat?

“Safely checking the switch would entail using a voltmeter/multimeter with the ability to read resistance/ohms. Place the two leads of the meter on each wire/terminal of the neural safety switch. Set the meter to read ohms; this will check for electrical continuity.

Where is the shift interrupt switch?

The shift interrupt switch is on the top of the motor. I has a metal arm that bends when you push the throttle. I believe when you check the timing you actually connect two white wires on the drivers side of the motor (not the shift interrupt switch cables).

What is throttle friction?

A pilot-operated device to stiffen the movement of the throttle lever(s) so as to effectively lock it in the set position and prevent it from slipping back to any selected setting.

When did Mercury introduce DTS?

Mercury introduced DTS as an integral part of its Verado line in 2004, and today offers digital controls on Verado from 135 to 350 horsepower, the broadest range of any manufacturer.

What does DTS mean on a boat motor?

SmartCraft DTS (Digital Throttle & Shift) delivers precise and smooth handling with instant response and total control.

What is a boat throttle called?

An outboard motor shifter and throttle control is the unit that controls the amount of throttle or speed of the outboard motor. The throttle control is a lever that can be pressed forward to increase the speed of the boat.

How do I know if my shift cable is bad?

Indicator doesn’t match the gear. If the shift selector cable is going bad, the indicator light or cable will not match the gear you are in. …
Vehicle will not turn off. …
Vehicle starts in another gear. …
Vehicle will not go into gear.

Can you adjust automatic transmission?

The technicians at All-Automatic Transmissions understand that problems with your vehicle’s transmission can often be resolved with adjustments or a minor repair. In fact, a simple adjustment can be done without even removing the transmission from the vehicle.