What does f2 mean on Kenmore Elite washer

The F2 fault code indicates a problem with the washer’s drain system, and you must troubleshoot the problem to determine how to fix the washer and clear the code.

What does F2 mean on a washing machine?

: The “F2” fault code indicates it’s taking too long to drain the tub of water in order to reset the pressure switch. The problem is that the washer is not always able to drain water so that the water level switch can reset. This can happen if the wrong type of detergent is used or if you are using too much.

How do I clear the error code on my Kenmore washer?

1. Look for the “Pause/Cancel” button on the washer control panel. …
2. Press the “Pause/Cancel” button twice to cancel the wash cycle. …
3. Connect the water supply hoses back to the washer and turn on the water spigots.

How do I fix error code F02?

Press the pause or cancel button on the Whirlpool washing machine to clear the F02 error code from the display, and try using it again. The error code is displayed when the washer takes more than eight minutes to drain, but may just be a glitch.

How do I force my Kenmore Elite washer to drain?

1. Place the bucket behind the washer next to the drain hose.
2. Unhook the drain hose from the drainpipe. …
3. Squeeze the locking pin on the end of the drain hose that is connected to the back of the washer if you will be draining the water into a floor drain.

What does F2 error code mean?

Oven Repair. If your GE oven has an F2 (or F20) error code, the oven is detecting that the temperature inside the oven has exceeded a preset threshold. In plain English, it means the temperature has exceeded 615 degrees, or 915 degrees Fahrenheit during a self-cleaning cycle.

How do I fix the F2 code on my Kenmore washer?

Electrical connections run from the control panel to the side of the pump to power it. Over time, the vibrations caused by the washer could loosen the wire connections and keep the pump from performing its job. Checking the pump for secure wire connections can clear the F2 error code on your Kenmore washer.

What does Sud mean on Kenmore Elite washer?

If “Sud” is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent.

What does f2e2 mean on Whirlpool dryer?

The Whirlpool Duet Dryer Error E2 means the control has detected that the thermistor is shorted. This error can be a wiring issue from the control to the thermistor or a bad thermistor. In some cases it can be a bad control reporting false errors but this is not common.

What does f2 mean on Hotpoint washing machine?

Error CodesFault TypeF02Motor faultF03Temperature sensor faultF04Blockage or pump issueF06Door lock problem

Article first time published on

How do you unlock a Kenmore Elite he3t washer?

There is a tab on the bottom of the door lock assembly that you can pull until it clicks to manually unlock the washer door.

How do you put a Kenmore Elite washer in diagnostic mode?

1. With the washer empty, close the door.
2. Push “control/on” or “Start”
3. Select “Drain/Spin”
4. Select “No Spin” by pressing SPIN SPEED touchpad.
5. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
6. C:00 should light up and begin the diagnostic.

What does 03 mean on a Kenmore washer?

@ronhurley the error code “OE” is a “Drain error ” and it is initiated by your washer not having fully drained in 10 minutes. Most common cause is a clogged filter. Check your “coin trap” filter for retained objects, like missing socks etc.:-) To clean it.

Why is my Kenmore Elite washing machine not draining?

A Kenmore washer that won’t drain properly likely has a clogged pump. Try checking the drain to see if there’s any foreign object obstructing the valve or opening. If not, the drain pump might be damaged and need replacing. Those with newer washer models can also try performing a master reset.

Why is my Kenmore Elite washer not draining?

If the washer won’t drain water the drain pump might be defective. It’s also common for a small sock or other article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump. If the washer won’t drain there might be a clogged pump or hose.

How do you reset a Kenmore Elite he3t washer?

1. Press the “Stop” button twice, and then press the “Power” button. Video of the Day.
2. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
3. Press the “Start” button to complete the reset process and restart the washing machine.

What does F2 mean on a Kenmore oven?

The “F2” fault code indicates the oven got too hot. Let the oven cool down before reconnecting the power cord. If “F2” displays when cold, this could indicate a faulty electronic oven control board or a faulty oven temperature sensor probe.

How do I turn off F2 on my Whirlpool oven?

Press and hold any key to clear the error code and F2 code should appear. Select ‘cancel’ and observe for one minute for errors. If error continues, disconnect power and replace control.

How do I clear my Whirlpool f9e0 code?

1. Power unit down by turning off the circuit breaker(s) for one (1) minute.
2. Monitor the range or oven for one (1) minute to ensure the error code does not display again.
3. Verify the range or oven operation.

What does f2 mean on a Whirlpool dishwasher?

Whirlpool gold series dishwasher error code e2/ f2, means main control board is not getting correct signal from the user interface. Turn off power/breaker, remove screws holding inner door liner, remove liner and check/secure/clean all wire connections from front interface and main control board.

What does F5 and E2 mean on a washing machine?

The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.

What does E2 mean on Whirlpool washer?

An E2 Error code indicates that the washer is still draining after 8 minutes. Check the following: Check that the drain hose is not more than 391 ⁄3″ (100 cm) from the floor. Remove any clogs from the drain hose.

How do I reset my Kenmore Elite HE4t washer?

1. Press and hold “Drain & Spin” for three seconds to release the child lock, if the keypad is locked. …
2. Press “Pause/Cancel” twice to cancel the current operation.
3. Turn off and unplug the washing machine.
4. Wait several minutes before restoring power to properly reset the machine.

What does F35 mean on a Kenmore Elite washer?

The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor.

How do I fix the Sud error on my Kenmore Elite washer?

SUD : The Sud error code is used to indicate there are too many suds for the washer to remove. This is often caused by too much detergent being used or non HE detergent being used in an HE machine. Run the machine through a Rinse/Spin cold water cycle then a Normal cycle without adding any additional soap.

What does F05 mean on my washing machine?

F05 — Waste pipe blockage or pump issue. Issue: Washing Machines door will not open / the door can be opened but water remains inside the drum. Advice: Please check for blockages in your pump filter (if applicable to model – please see user handbook).

What does F12 mean on washing machine?

F12 — Electronic control fault. Issue: Washing Machines is not operating (turning on).

How do I force my Kenmore washer to unlock?

1. Touch “Control Lock” for five seconds until “CL” disappears from the washer’s display to unlock the control panel.
2. Press “Start/Pause” to manually pause the cleaning cycle. …
3. Pull the door’s handle to open the door and add or remove the clothing from the washer.

How do I turn off the control lock on my Kenmore washer?

You’ll want to hold down the drain and spin button to unlock the control board. It states this information underneath the button. You may have to hold it down for longer than three seconds to unlock.

Where is the coin trap on a Kenmore Elite washer?

Once you have the panel removed, you will see a white plastic unit, that is your pump assembly. You should also see a round plug with a plastic tab across the front (number 14 in the explosion drawing). That is your coin trap.

What does ND mean on a Kenmore washing machine?

The nd error code on your Kenmore front-load washer means water isn’t draining from the washer. The likely causes are a stopped-up washer drain or a clogged drain pump filter.