What does Ld code mean on Whirlpool washer

If Ld (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water.

How do you fix a Le error on a Whirlpool washing machine?

An LE error code on the washer’s display indicates that the motor is locked, possibly due to a heavy wash load. Large and heavy sized loads will put a strain on the motor, causing the LE code to occur. Performing a reset on the washer will normally resolve this error with a reduced load size.

How do you reset the code LD on a top Whirlpool Cabrio Platinum?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do you fix a washing machine DL?

1. Check the door of the washing machine. Clothes or other foreign matter are probably stuck.
2. Perform a hardware reboot. Turn off the washer for 10 minutes, then turn it on again and select the desired program.
3. Make sure the cover is closed properly. …
4. Inspect the elements of the lock.

What does Ld mean on a Speed Queen washing machine?

Speed Queen Ld – Long Drain.

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

What does error code Ld mean on Maytag washer?

“F32,” “Ld” or “C8” error codes indicate a slow or stopped drain pump, and “C6” indicates that the recirculation pump has stopped. Remove the pumps to access and remove the items clogging them. Unplug your Maytag Bravos washer from the electrical outlet.

What does DL stand for on washing machine?

: DL is a failure of the door to lock. The door must lock before any cycle begins. This can be caused by any of the following conditions: The door lid is not completely closed due to an interference. Wash media buildup is preventing the lock bolt from extending.

How do you clear the error code on a Whirlpool top load washer?

System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).

What does F11 mean on a Whirlpool washer?

The F11 error code in the Whirlpool washer reports about the engine control board malfunction. Having found out this, a user will immediately adhere to household appliance repair specialists.

Article first time published on

What is the meaning of DL in washing machine?

A DL error on an LG washer indicates that the door lock switch doesn’t work properly.

How do you manually unlock a Whirlpool Cabrio washer?

1. Press/hold for 3 seconds.
2. Release for 3 seconds.
3. Press/hold for 3 seconds.
4. Release for 3 seconds.
5. Press/hold for 3 seconds.
6. Release.

Why is my Whirlpool Cabrio washer not draining?

Check the washer’s discharge hose if the water fails to drain from the washtub. Look for any kinks in the Cabrio washer’s discharge hose that could stop the water from draining. Straightening the hose ensures proper draining. … Test the drain pump to ensure it has not failed if the washer still will not drain.

What does whirlpool diagnostic mode do?

Whirlpool Belt Drive Washer Diagnostic Mode & Tests The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.

How do you unclog a Maytag drain pump?

If something is caught in the drain pump, you’ll need to unhook the belt from the drain pulley underneath. Grasp the clogging item with your needle-nose pliers and twist the pulley to unwind the item from the drain assembly. Pull the clogging item out from the top of the pump, where the drain hose was connected.

How do I know if my drain pump is bad?

Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn’t turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn’t, this is a sign the pump is dying. For front-loading washers, do not attempt to open the door mid-cycle.

Why is my Whirlpool washer not draining or spinning?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

How much does it cost to replace a washing machine drain pump?

Washing machine pump 2 repairs are usually required when you note active leaks or a tub that doesn’t drain. If a pump is no longer working, it’s a relatively easy fix for a contractor and extends the lifetime of your appliance. On average, expect to spend $300 to $400 for a pump replacement job.

How do you manually unlock a Whirlpool front load washer?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

How do I reset my front load washer?

1. Press POWER to turn the washer off.
2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
4. Plug the washer back in, or turn the circuit breaker back on.

Why does my Whirlpool washer not start?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

Why is my Whirlpool washer beeping?

Error “Beeps” are an audible signal that the machine makes to alert the user that something is not right. Typically this will happen if the washer door has not been opened and closed for at least 3 cycles. This code may appear when the washer is first turned on. Open and close the door to clear the display.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

How do I fix my E1 error on my Whirlpool washer?

1. Check that the water faucets are not closed.
2. Check that the water pressure in the house is over 20 kPa.
3. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
4. Check that the drain hose is not below 27½” (700 mm) from the floor.

How do I fix E1 error?

1. Turn off the air conditioner and unplug it.
2. Hold down the power button, and keep it depressed while you or someone else plugs it back in. Keep the button depressed while the fan and condenser cycle run briefly and cycle off again. …
3. Unplug the air conditioner again and plug it back in.

Why does my washing machine Show E1?

When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water. If problem persists, contact our Samsung Call Centre for further assistance.

What does f1 mean on a Whirlpool Duet washer?

The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.