What size is 6an fuel line

Male Thread SizeAN Size*Equivalent Tube Size (Nominal OD)7/16-204AN1/4″9/16-186AN3/8″3/4-168AN1/2″7/8-1410AN5/8″

What size is an AN6 fitting?

Where every dash number is 1/16 of an inch an AN6 fitting would be equivalent to 6/16″ or 3/8″ Fitting size.

What is 6AN thread?

AN SizeHose i.d. – Tube o.d.SAE Thread Size-41/4 in.7/16 in.-20-55/16 in.1/2 in.-20-63/8 in.9/16 in.-18-81/2 in.3/4 in.-16

What does AN6 mean?

Note that AN threads are different for bolts and fittings. In bolts the number refers to the diameter of the bolt whereas in a fitting it refers to the OD of the tube and thereby have different threads. For example, AN6 bolt has a 3⁄8-24 thread whereas an -6 AN fitting has a 9⁄16-18 thread.

What are fuel line sizes?

Recommended Fuel Line Size (from the tank to the pump)Engine OutputSize (inches)Size (AN)350 hp or less5/16 in.-5350-450 hp3/8 in.-6450-650 hp1/2 in.-8

What size wrench fits a 6AN fitting?

Stainless Tubing AN Equivalent All dimensions are in inches unless otherwise noted.ANTube Size ODWrench Size-55/16″N/A-63/8″11/16″-81/2″7/8″

How much power can 6 an fuel line support?

at 45 psi for engines producing up to 870 hp naturally aspirated, or 725 hp forced induction. Its rated at 70gph free flow and a max psi of 65psi.

What is the ID of 3/8 fuel line?

Part Number: 555-15996. 3/8 in. I.D.

What size is an 6 in MM?

FITTING SIZEHOSE O.D.F-33/16″ (4.76mm)0.312-4¼″ (6.35mm)0.364-6⅜″ (9.53mm)0.481-8½″ (12.70mm)0.660

How do I know what size hose I need?

Simply put, a dash size refers to an I.D. of a hydraulic hose or fitting in 1/16″ increments. For example, -6 hose would indicate a hose with I.D. of 6/16″ – or 3/8″. Hoses are measured by inside diameter, unlike tubes which are measured by outside diameter.

Article first time published on

What thread size is a 6AN fitting?

Male Thread SizeAN Size*Equivalent Tube Size (Nominal OD)9/16-186AN3/8″3/4-168AN1/2″7/8-1410AN5/8″1 1/16-1212AN3/4″

What size thread is an 8?

AN SizeMetal Tube O.D.Thread Size81/2″3/4-16 SAE105/8″7/8-14 SAE123/4″1-1/16-12 SAE161″1-5/16-12 SAE

How much HP is 6AN good for?

“A rule of thumb; 5/16″ (-5AN) will support up to 300 horsepower, 3/8” (-6AN) will cover up to 500 HP, and 1/2″ (-8AN) is good to 700HP.”

Is 3/8 fuel line big enough?

A 3/8”id fuel line can easily support 600 HP given sufficient “pump head”! Given a big enough pump a 3/8” steel line could support 1000 HP. … If the pressure falls as the engine RPM’s go up you need more pump head. More pump head can be achieved with a bigger pump, higher pump voltage and/or increasing the line size.

How do I know what size fuel line I have?

Place the top of a 1/4-inch wrench with an open end over the fuel line. Slide it carefully over the line so that it fits snugly against the tubing. Read the wrench’s measurements to determine the diameter of the fuel line.

Does size of fuel line matter?

Does size really matter when it comes to fuel lines? According to the fuel delivery system experts at Fuelab, it does. It’s because fuel line size and length have a direct effect on the amount of fuel pressure drop your fuel system will experience.

What size is lawn mower fuel line?

Most are 1/4″. But, the new fuel lines are sometimes that new material that is thinner than old fashioned rubber, and has no cloth strings in them. It is smaller outside and needs smaller clamps, depending on what you like to use. ME….

Can a fuel line be too big?

However, in fuel line we are talking about diameters in fractions of inches and line length in multiple feet, so wall friction tends to dominate. Assuming everything is sized correctly, you cannot be too big with a remote pump/regulator set up.

What size is 6AN wrench?

-6AN is an 11/16″ wrench. The next size up -8AN, is a 7/8″ wrench. socket or wrench/vise with masking tape, to avoid scratching the fitting.

What size an is 3 8?

AN SizeMetal Tube O.D.Thread Size-3 AN3/16″3/8″ – 24 SAE-4 AN1/4″7/16″ – 20 SAE-5 AN5/16″1/2″ – 20 SAE-6 AN3/8″9/16″ – 18 SAE

What size is a #8 hose?

HOSE I.D (Inches)All EXCEPT Transportation & Refrigerant Hoses-63/810-81/212,5-105/816

What is 3/8 of an inch in Millimetres?

Dimensions — Inches to Metric0.375”3/8”9.53 mm0.438”7/16”11.13 mm0.500”1/2”12.70 mm0.563”9/16”14.30 mm

What is 6mm in fraction?

DecimalFractionMetric0.19695 mm0.21887/325.56 mm0.23626 mm0.25001/46.35 mm

How many MM is a quarter?

DenominationCentQuarter DollarDiameter0.750 in. 19.05 mm0.955 in. 24.26 mmThickness1.52 mm1.75 mmEdgePlainReededNo. of ReedsN/A119

What is the outside diameter of 3/8 inch fuel line?

X 5/8 ” Od.

What is the outside diameter of 3/8 rubber fuel line?

FUEL LINE HOSE 9.5MM (3/8″) NITRILE TUBE ID 10MM X OD 16MM NON-FUEL INJECTION 50 PSI – Collier & Miller.

What size is fuel line hose?

For fuel injection hose, sizes range from 3/8 inch to 3 ½ inches. Choosing sizes depends on the size of fuel injectors. The common sizes are 5/16, 5/8, 3/8, 1/2, and 3/4 inches.

How do I know what size hose to get?

Inner Diameter. …
Outer Diameter. …
Length. …
Flow Rate. …
Size. …
Temperature. …
Application. …
Media.

What is the ID of 3/8 hose?

Dash SizeInside Diameter-55/167.9-63/89.5-81/212.7-105/815.9

ARE AN fittings the same as JIC?

JIC fittings are dimensionally identical to AN (Army-Navy) fittings, but are produced to less exacting tolerances and are generally less costly. SAE 45-degree flare fittings are similar in appearance, but are not interchangeable, though dash sizes 2, 3, 4, 5, 8, 10, 14, and 16 share the same thread size.