Why does my Onkyo receiver have no sound

Incorrect settings on your Onkyo receiver can result in no sound. The digital input signal should be set to “Auto.” Select the correct digital input source. Unplug headphones from the receiver when you are trying to use your system with the external speakers. … Adjust the volume controls so you can hear sound.

Why is my receiver not producing sound?

Make sure the input devices are playing audio. Make sure the VOLUME or MASTER VOLUME knob of your AV Receiver is not set to VOL MIN. … Make sure headphones aren’t connected to your receiver or input device. Press the SPEAKERS button on your receiver and select a setting other than OFF SPEAKERS.

How do I get my Onkyo receiver out of Protect Mode?

Unplug the receiver’s power cord from the wall and leave unplugged for at least one hour. …
Reconnect the power cord after at least one hour has passed. …
Turn the receiver on and turn the volume to the maximum setting. …
Turn the volume back to the minimum setting and turn off the receiver.

How do you troubleshoot an Onkyo receiver?

Reset the Onkyo if you continue to have trouble. Hold the “VCR/DVD” button while pressing the “On/Standby” button, and the receiver should enter “Standby.” Turn it on again by pressing the “On/Standby” button.

Why is my amp on but no sound?

If the car amp has power but not sound in the amps, you can check its input connected to the head unit. Check the RCA cables that connect the amp to the head unit. … To test your amp, hook the test sub to all the channels in your amp one after the other. This should reveal any issues with the output.

How do I get sound on my Onkyo RECEIVER?

Press the “Muting” button on the remote control to unmute your Onkyo receiver. Check the inputs and outputs to ensure they are correctly connected to the receiver. Adjust the volume controls so you can hear sound.

How do I know if my receiver is bad?

Connect a different speaker to right front output. If you hear the static it’s the receiver. If you don’t it’s probably the speaker. You could also move the right front speaker to the left front output and see if you hear anything.

How long do Onkyo receivers last?

My expectations are that a receiver should last at least 10 years. Onkyos have tons of features, but I would take durability over features. I just replaced my Onkyo with a Pioneer (now owned by Onkyo). Hopefully it will have better durability.

How do I turn on Onkyo surround sound?

Plug in the five surround speakers to the back of the surround sound receiver. …
Plug in the subwoofer cable into the “Subwoofer” port on the back of the receiver.
Place your speakers around the room. …
Connect your devices to the surround sound receiver.

How do I test my Onkyo receiver?

To setup your receiver to output the test tone from the speakers, press the Setup button and select Speakers>Manual Setup>Level>Test Tone Star. You can now select and adjust the speakers’ audio level using the “UP, DWN and SIDES arrows” buttons on your remote control.

Article first time published on

Do Onkyo receivers have fuses?

There may be more than one fuse as is the case with HK receivers. If you can source the fuse(s) for replacement this may correct the problem assuming they are blown. In most receivers the fuses have an almost thread-like wire so you will have to examine them under good light.

Why does Onkyo receiver shut off?

When you connect the bad wire or speaker the receiver will shut down. If after you connect them all if the receiver now stays on then there was a short where the wires were connected to the receiver that you repaired when you replaced them.

What does it mean when your amp says protect?

Amplifier protection mode is a shutdown state that car amps may enter in certain situations. The purpose of the shutdown state is to prevent damage to the amp or other system components. So while dealing with an amp in protect mode may be annoying, it might save you from a bigger headache down the road.

Why does my receiver shut off by itself?

In many cases, premature shutoff of your unit can be caused by a problem with the speaker wiring between the receiver and speakers. A single strand of wire in the wrong place (causing a short circuit condition) will cause the unit to shut off at anything but very low volume levels.

How do you know if your amplifier is blown?

There is a noticeable distortion in the sound.
There is no sound even if you have already turned on your audio system.
Your stereo system starts making bizarre sounds such as farting sounds.

How do you tell if a speaker is blown without hooking it up?

Yea if it’s hard to push down the speaker cone, then it’s probably blown. You can sometimes also smell the cone. If it smells like something was burnt, that also is a telltale sign that your speaker is blown.

Will an amp still turn on with a blown fuse?

If the fuse is present and blown, the amp can’t turn on because the circuit providing mains voltage is open. Simply replacing the fuse may or may not solve the problem.

How do you troubleshoot a sound system?

Run the audio troubleshooter. …
Verify that all Windows Updates are installed. …
Check your cables, plugs, jacks, volume, speaker, and headphone connections. …
Check sound settings. …
Fix your audio drivers. …
Set your audio device as the default device. …
Turn off audio enhancements.

Why does my stereo have power but no sound?

Typically when a car stereo produces no sound it’s usually caused by a shorted or grounded wire, defective speakers, faulty head unit/fuses, or setup is not yet complete with your radio unit.

Why does my home radio have power but no sound?

Silent stereos are usually caused by low power, a wrong source selection, disconnected or faulty speaker wires, broken speakers, or a malfunctioning source component. … Remember to always turn off the power to the system and components before connecting or disconnecting cables and wires.

How do I connect my Onkyo surround sound to my TV?

Just use the HDMI 1 port on the back of your TV. Connect the other end of the cable to your receiver. You’re looking for something labeled HDMI Out; it’s usually a different color. If necessary, connect a digital optical cable to the back of your TV (optical out), and the other end to your receiver (optical in).

How do I reset my Onkyo TX nr616 RECEIVER?

I decided to do a factory reset by turning it on, then press the CBL/SAT button while pressing the power button.

How do I reset my Onkyo TX nr636 RECEIVER?

Press and hold down 2HOME until the 3 remote indicator lights (about 3 seconds). Within 30 seconds, press 1RCV again.

How do I program my Onkyo RECEIVER?

Locate the number code for the device (TV, DVD player, etc.) …
Hold down the remote mode button for the intended device (DVD, VCR, TV, etc.) …
Use the number keys to enter the four- or five-digit (depending on the model) code for that device within thirty seconds.

What is the best listening mode for Onkyo?

All Channel Stereo can be used on 5.1 and 2.0 Sources, but I prefer Dolby Digital or THX Cinema for 5.1 Sources as there is Discrete Information for each Channel with 5.1 Sources. However, whatever sounds best to you is fine. Some enjoy having all Channels playing at a high volume like with All Channel Stereo.

What is direct mode on Onkyo?

Direct: shuts down some processing in the unit for a cleaner audio signal. The sound is reproduced using the same number of channels as in the source material. Full Mono: all speakers output the same sound in mono.

How do I connect to my Onkyo speaker?

Locate and tap the Apps Menu.
Locate and tap the Settings icon.
Select the Bluetooth. You may need to select Connections first.
In the list of Available Devices, choose the Bluetooth accessory you wish to pair with.

Is Onkyo going out of business 2020?

Onkyo was declared insolvent but they failed to file for bankruptcy with many who have looked at the books and the debt tipping that this could still happen despite the confidence of management. In 2020 Onkyo reported a global revenue decline of 49.3% in its fiscal year 2020 with a record net loss of over $90 million.

Do Onkyo receivers sound good?

No wonder, as the Onkyo receivers have incredibly high quality and can provide mind-blowing sound. I analyzed a lot of different devices to find the best Onkyo receiver. … The peculiarity of Onkyo home theater receivers is to offer high power, thanks to the house WRAT technology (Wide Range Amplifier Technology).

Can I leave my Onkyo receiver on all the time?

It is not bad to leave AV receivers and amps on all the time as most stereo equipment is set up to use minimal power and will go into standby mode when not in use. So leaving AV receivers and amps on or turning off between uses are both safe.